[. . . ] Screwdriver Required for Assembly rj 3l-e il, lr;. . zzi\ \'rri \/\-?/ 'rOTE One c'ihg 61955 [?t I i/ lj I I I | . r- tN) (x8) ro-itottorv End \_V_ Cr* Tube5 (x6) T:5es witl be a differert r, co;o (T) Headboard Adapter Plate (2x) C=1 V I 1r9!e Bracket (4x) 6Fl*) rhreaded End UossTubes (x+1 , k ii. iiiiiiiiii:'uori. 'i ;, . iri:i:i:i:r 5 Parts Needed: Refer to p9. 5, "Crib Parts" (N) To aid in the assembly process, Place one of the Mattress Support posts on the floor and against a wall for balance. [. . . ] 5, "Crib Parts" (N) To aid in the assembly process, Place one of the Mattress Support posts on the floor and against a wall for balance. with the 10 large holes facing inward, and the 4 srnall holes facing out, make sure the"Bottom" sticker is facing the floor. -, -a I \J i r-- (N) a (N) i a \-/ 3 e l (N) i i (P o o lnsert the Threaded Cross Tubes (R) into the first, fourth, seventh, and tenth holes of the Mattress Support Post (P). Loosely hand tighten 4 Short Cone Head bolts (N) into the holes that line up with the Threaded Cross Tubes (R) (This will allow further adjustment while assembling Hollow Cross Tubes). Including the different color tube containing the instructions envelope. Assemble the second Mattress Support Post (P) on to the cross tubes (make sure "bottom" sticker is facing down). Starting at one end, loosely hand tighten each bolt making sure Hollow Cross Tubes (a) are properly in place. Do not tighten bolts until you have all B (r) (N)A (N)A ($A t*rp bolts inserted on both Mattress Support Posts. Attaching Angle Brackets. Attach the Anglg Bracket (O) to the end of the Mattress Support Post (P) using one of the long cone head bolts (M). Loosely attach the "leg" of the Safety Rail to the underside of the Mattress Support using one of the short Allen Bolts (J) through connectors. Repeat procedure with the other Safety Rail. RE-CHECK ALL FASTENERS ON ENTIRE CRIB TO BE SURE THEY ARE TIGHT. (J) (xl) -/ ottom view of Connector Piece. N(r) $##i*ffiii, riiii* (x2) (H) (x4) 9 YourTransitional Bed can be converted to a Child's Daybed by simply removing the Safety Rails. Always return instructions sheet to envelope attached to the mattress support. . lf you are converting from the crib directly to the child's daybed. Please make sure that the mattress support is in the lowest position. RECHECK ALL FASTENERS TO BE SURE . THEY ARE TIGHT. IT IS GOOD TO ALSO DOUBLE CHECKTHOSE NOT USED IN THIS CONVERSION. NOTE: To convert back to a Child's Crib, remove the safety rails and repeat steps 5& 6. By utilizing your Ellis crib"Back Side"Asse''r'rl-'-1"", '3'-1r f lli< (rc" ( "-*headboard for a full sized bed. [. . . ] Please make sure that the mattress support is in the lowest position. RECHECK ALL FASTENERS TO BE SURE . THEY ARE TIGHT. IT IS GOOD TO ALSO DOUBLE CHECKTHOSE NOT USED IN THIS CONVERSION. NOTE: To convert back to a Child's Crib, remove the safety rails and repeat steps 5& 6. By utilizing your Ellis crib"Back Side"Asse''r'rl-'-1"", '3'-1r f lli< (rc" ( "-*headboard for a full sized bed. [. . . ]